The Foundation of Plumbing Knowledge for Bathtub Installation
The Foundation of Plumbing Knowledge for Bathtub Installation
Blog Article
Presented here below you can discover additional amazing guidance in relation to A Step-by-Step Guide to Installing a Bathtub.
Installing a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a moderately challenging job. If the old tub is conveniently obtainable, the job can move quickly; if you need to open up a wall to eliminate the old bathtub and place the new tub, the job is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly need a helper to leave the old bathtub as well as set in the new one. Make certain you have actually qualified yourself for the task and fit attempting it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This post will certainly assist you set up a brand-new tub in your shower room if you have actually already purchased a brand-new bathtub as well as do not require to transform the plan of your previous water pipelines.
Your devices as well as material checklist ought to make up the following:
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bathtub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will originate from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Before carrying on to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks as well as tighten them if required. Load the bathtub as well as also check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub needs to wait until the tub has been utilized a minimum of once as this will settle it into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines are in area in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is securely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The previous type needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall in between the bath as well as the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, and can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to permit the motion experienced when the tub is in use. The sealer can crack rather very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that piece of writing on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a search on the internet. So long as you enjoyed reading our blog post if you please do not forget to share it. Many thanks for your time. Visit again soon.
24/7 plumbers for emergencies. Report this page